OFFICIAL SPONSORS
Sports Trainer |
Email: cardiotrek@gmail.com Hours: Tues-Thurs 10-5:30, Sat-Sun 10-3:30 |
|
Saturday, January 30, 2016
Why do people put up with shoddy bicycle assembly?
By Smokey Dymny,
of the Quadra Bike School
Edited by Charles Moffat,
The Bicycle Mechanic
Just before I closed up my shop on Quadra Island, B.C. for the Christmas break a young woman brought me a $3000+ downhill bike to straighten the derailleur hangar she had bent for the second time. (The bike was three months old.) She said the first time it had been straightened by the shop in Squamish, B.C., which had originally sold her the bike. Now she was living on our island off the east coast of Vancouver Island.
I cautioned that I could only straighten the derailleur if the back wheel was true, and she agreed I could true it if necessary. (A minor truing usually takes less than 15 minutes.) Now, this wheel was actually laterally true, but the spoke tension was terrible. Half the spokes on the drive side were close to the correct tension, and the alternate spokes were drastically low. After I re-tensioned this wheel I had to check the front wheel too, hoping it wasn’t as bad. But it was.
In under half an hour I saved her wheels from a potential catastrophic failure. What was deplorable was that a bike shop in a town known for hard-hitting downhill riding, a bicycle shop there would let an expensive cycle go out the door in such pathetic mechanical shape. They even had a chance to correct their sloppy work when she returned to get her derailleur hangar straightened.
I urge everyone buying bikes anywhere in Canada to start demanding that their local bike shops prove the proficiency of their mechanics. Take every bike from a “professional shop” to a community bike shop or clinic, get the volunteers to show you how to use a tension gauge and use it to check every spoke on the drive side of the rear wheel to see if it measures close to 100-120kgf. The front wheel should measure 80-100kgf (measure on the left side if it has a disc brake). If the wheels are not close, go right back to the shop and ask for a proper wheel truing or your money back.
Up till now bike shops have been slow to send their mechanics to professional training schools. I think they’re afraid they’ll have to pay them more. And they will. This has been an industry sleazing by with minimum-wage starting salaries, and only rising above that in minuscule increments. The riding public is suffering, only they don’t know it. When a wheel or other component fails drastically, I’ve seen service managers blame the customer for the fault and then charge them for the repair even within the very short warranty period offered by most shops.
Only bike riders who won’t take bad treatment will make these shops shape up.
Being a rider on the streets of Canadian cities is not for the faint-hearted. Riding a bike assembled to shoddy standards should be an offense under your local highways act.
Editor's Note: Some bicycle shops don't even have a spoke tension gauge. A true sign they don't know what they are doing. They're not even expensive, and they really should be mandatory in every bicycle mechanic's bag of tools. There are many different kinds of spoke tension gauges (like the three shown below) and there is no excuse for not having one and learning its proper use.
of the Quadra Bike School
Edited by Charles Moffat,
The Bicycle Mechanic
Just before I closed up my shop on Quadra Island, B.C. for the Christmas break a young woman brought me a $3000+ downhill bike to straighten the derailleur hangar she had bent for the second time. (The bike was three months old.) She said the first time it had been straightened by the shop in Squamish, B.C., which had originally sold her the bike. Now she was living on our island off the east coast of Vancouver Island.
I cautioned that I could only straighten the derailleur if the back wheel was true, and she agreed I could true it if necessary. (A minor truing usually takes less than 15 minutes.) Now, this wheel was actually laterally true, but the spoke tension was terrible. Half the spokes on the drive side were close to the correct tension, and the alternate spokes were drastically low. After I re-tensioned this wheel I had to check the front wheel too, hoping it wasn’t as bad. But it was.
In under half an hour I saved her wheels from a potential catastrophic failure. What was deplorable was that a bike shop in a town known for hard-hitting downhill riding, a bicycle shop there would let an expensive cycle go out the door in such pathetic mechanical shape. They even had a chance to correct their sloppy work when she returned to get her derailleur hangar straightened.
I urge everyone buying bikes anywhere in Canada to start demanding that their local bike shops prove the proficiency of their mechanics. Take every bike from a “professional shop” to a community bike shop or clinic, get the volunteers to show you how to use a tension gauge and use it to check every spoke on the drive side of the rear wheel to see if it measures close to 100-120kgf. The front wheel should measure 80-100kgf (measure on the left side if it has a disc brake). If the wheels are not close, go right back to the shop and ask for a proper wheel truing or your money back.
Up till now bike shops have been slow to send their mechanics to professional training schools. I think they’re afraid they’ll have to pay them more. And they will. This has been an industry sleazing by with minimum-wage starting salaries, and only rising above that in minuscule increments. The riding public is suffering, only they don’t know it. When a wheel or other component fails drastically, I’ve seen service managers blame the customer for the fault and then charge them for the repair even within the very short warranty period offered by most shops.
Only bike riders who won’t take bad treatment will make these shops shape up.
Being a rider on the streets of Canadian cities is not for the faint-hearted. Riding a bike assembled to shoddy standards should be an offense under your local highways act.
Editor's Note: Some bicycle shops don't even have a spoke tension gauge. A true sign they don't know what they are doing. They're not even expensive, and they really should be mandatory in every bicycle mechanic's bag of tools. There are many different kinds of spoke tension gauges (like the three shown below) and there is no excuse for not having one and learning its proper use.
Subscribe to:
Posts (Atom)
NOTE
Spam comments will not be approved. If you want to advertise your product or service (or want to sponsor this blog) please send an email.
Popular Posts
-
Need some extra carrying capacity on your bicycle? Maybe enough to take a whole extra person with you? Basically what happened was I was...
-
Bottom Bracket - The assembly between the pedals that allows the Crankset to rotate. Bottom Bracket Shell - Part of the bicycle frame that c...
-
Bike shops are ALWAYS looking to hire more bicycle mechanics, especially in the Spring. The problem however is the Old Catch 22... they on...
-
BRAKE LEVER TERMINOLOGY Adjusting Barrel - A hollow screw used to change the length of the brake inner wire. Barrel Locknut - A nut that hol...
-
By Smokey Dymny from the Quadra Bike School Too many beginners jump on a bike without knowing exactly how to set it up for comfort. The w...
-
The suspension in the front forks of a bike takes a lot of stress. All the weight of the rider and all the bumps and bounces of the terrai...
-
Since bicycles have been around since the 19th century there are many different thread standards that have been used. Standards also vary fr...
-
Ignore the photo on the right... its not really a cycling shirt. ;) What I want to pass on this time is clothing. Specifically cycling shi...
-
Bicycle chains turn black over time as the chain lube collects dirt and grit while riding or locked up outside. This is unfortunate and affe...
-
Is it a bicycle? Or is it a baby stroller? Or is it an expensive death trap for your toddler? The Dutch sure do love their bicycles, so its ...
About the Author
Charles Moffat is equal parts bicycle mechanic, cyclist, painter, sculptor, fantasy writer, poet, website designer and pun maker. For more details see charlesmoffat.com.
CONTACT INFO
Email
JOB POSTINGS
Do you own a bike shop and are looking to hire a bicycle mechanic in North America? Just email me with the job posting details and I will post it for you. (Also, please let me know when the job has been filled so I can update the posting.)
SELL YOUR OLD BIKE
If your bicycle is basically junk and you don't know what to do with it then SELL IT TO ME. I will use it for parts. I will give you a fair price ($20 to $30) for your old clunker just so I can rip it apart for parts.
If you need repairs check out my Bicycle Mechanic Services in Banbury-Don Mills.